Stock Request
*
Quantity Required:
Article Number:
*
E-mail Address:

Can't find a product?
*
Just ask:
*
Contact email:

Recently Viewed

Lewmar - Replacement Hatch Acrylics (Low & Medium Profile)

Lewmar

Replacement acrylics/lenses are available for Lewmar Low and Medium Profile hatches. Click on the hatch identification tab below to help you identify your hatch. Whilst we do keep some acrylics in stock, the range is vast and many will be made to order. Delivery time may be 3 - 4 weeks from date of order.

Price:  £105.95(Inc. VAT @ 20%)
+
Hatch type:  
Hatch size:  
Acrylic colour:  

Article Number:  360840900

  (3 Reviews)

Hatch acrylics and seals
Size Hatch overall size Hatch cut-out size
Width (X) Height (Y) Width (X1) Height (Y1) Radii (R1)
Size 00 281mm 281mm 211mm 211mm 42.5mm
Size 03 246mm 301mm 176mm 231mm 42.5mm
Size 10 330mm 330mm 260mm 260mm 42.5mm
Size 20 272mm 417mm 202mm 347mm 42.5mm
Size30  397mm 527mm 327mm 457mm 42.5mm
Size 40 491mm 491mm 421mm 421mm 42.5mm
Size 41 246mm 491mm 176mm 421mm 42.5mm
Size 44 512mm 512mm 442mm 442mm 42.5mm
Size 50 447mm 577mm 377mm 507mm 42.5mm
Size 54 462mm 577mm 392mm 507mm 42.5mm
Size 60 577mm 577mm 507mm 507mm 42.5mm
Size 65 560mm 675mm      
Bavaria L 556mm 556mm 486mm 486mm 42.5mm
Bavaria R 556mm 276mm 486mm 206mm 42.5mm
Bavaria S 330mm 330mm 260mm 260mm 42.5mm
Bavaria D 568mm 361.5mm 498mm 291.5mm 42.5mm

* Cut-Out sizes will change with Trim Kits are used.

  • Hatches should be fitted to a flat surface with a maximum tolerance of ± 1mm
  • Fastening size for lower frame sections use 5mm CSK screws No. 10 UNC 2BA
  • Fastening size at the hinge section use M6 (¼") screws
  • All hatches have a 'Lower Frame Flange' of 15mm

Lewmar Hatch & Portlight Fitting Guide (PDF)

Distinguishing between Lewmar Low profile and Medium profile hatches

These two variants look alike, but have differing hatch frame thicknesses.

  • Low profile hatch lids are 22mm thick
  • Medium profile hatch lids are 27mm thick

​Distinguishing between Mk 1 and Mk 2 hatches

The design of Lewmar Low and Medium profile hatches changed from Mk1 to Mk2 between July and December 2000, so if you are certain your hatch was constructed before or after this time then you should know which design you have.

If you are uncertain or require confirmation, then there are a few ways to check.

  • Roll pin.  Mk 1 hatches (left) have a visible roll pin (marked in the red circle), on the underside of the lid near the hinge, Mk 2 hatches (right) do not.

           

  • Lens code.  All Low and Medium profile hatches have a lens code, which is embossed on the underside of the lid next to the handle. *

Removing the Lid of your Low or Medium Profile hatch

Removing the frame to release the acrylic (& replace seal)

How to find your lens code

Average Rating (3 Reviews):  
Write a Review and share your opinions!

Rating:  
Very satisfied
Tuesday, 22 August 2017  | 

High quality item, prompt attentive service.

Was this helpful to you?  Yes  /  No

This review has not been appraised.


Rating:  
Exelent service
Tuesday, 6 September 2016  | 

Super service and knowledge!

Was this helpful to you?  Yes  /  No

This review has not been appraised.


Rating:  
posting to Holland
Monday, 5 September 2016  | 

Very fast delivery at reasonable price

Was this helpful to you?  Yes  /  No

This review has not been appraised.

Related products
Lewmar - Medium Profile Hatch

Lewmar - Medium Profile Hatch Part No. 39930020From:  £312.95  (1)

Lewmar - Ocean Hatch

Lewmar - Ocean Hatch Part No. 39610070From:  £299.00  (2)

Lewmar - Low Profile Hatch

Lewmar - Low Profile Hatch Part No. 39900030From:  £199.95  (2)

Lewmar - Joining insert kit (for Low & Medium Profile hatches)

Lewmar - Joining insert kit (for Low & Medium Profile hatches) Part No. 360925999£34.95

Lewmar - Friction hinge kit (for Low & Medium Profile hatches)

Lewmar - Friction hinge kit (for Low & Medium Profile hatches) Part No. 361263999£42.95  (2)

   

Click For details

 

 

 Search :